|
 |
| Cable Tester |
     |
|
PC based
Cable Tester
BieneCableTester01
|
|
BieneCableTester01
- is a high performance, low cost, portable PC
based Cable Tester for diagnostic wide
range of products, including cables, wiring harnesses,
distribution panels, wiring looms and switch assemblies.
Maximum numbers of connectors pin - 104. Cable Tester
display visually pinpoints problems when wiring
errors are detected, and offers one-second pass/fail
functional testing for cable production environments.
Test type: static, continuous static, dynamic (model
BieneCableTester01D).
An on-line base holds an unlimited number of User
cables. Choose from a wide variety of plug-in adapter
to mate with most standard cables. The system can
automatically learn a cable from a known good sample.
Tests PC cables, CISCO cables, Centronics and RS-232
cables, cables with connectors type DB Sub 9, 15,
25, 50, High-Density D-Submini 15, 26, 44, 62, Centronics
36, 50, SCSI cables - Centronics and miniCentronics
50 (SCSI-I), Ultra SCSI cables (MC68,80,100), miniD
50 (SCSI-II), miniD 68 (SCSI-III), V35, Telco cables
(Centronics 50), IDC and High-Density IDC Flat cables,
Router and Network Cables, Smart Serial Connectors
Cables. Tests cables for opens, short, pin-to-pin
configurations and misswired connections.
 |
BieneCableTester
- is portable PC based
Cable Tester that
connects to the parallel
port of your desktop or
laptop computer. For
testing any types cables
you will need an
adapters. This adapters
plug into two 60 pin
connectors.
Features:
- connects to the
parallel port (EPP mode)
- maximum 104x104 pin
cable testing
- static single or
continuous test for
shorts, opens and
misswired connections
- dynamic test (model BieneCableTester01D)
- faults identified for
opens, short, pin-to-pin
configurations, misswired
connections.
- create connection
table from sample-cable
- create cable wire
list
- save and print
results
- report error to
display or printer
- diagnostic self test
- user defined pin
names
- the software runs on
Windows 98.
- one-year warranty
with free technical
support; You will also
receive free software
upgrades.
Static test: this applies a voltage
to each pin in turn and checks the response of
all other pins (on the left and right connectors
of cables). Test runs one cycle for all pins.
This is checked against the required response.
This test will detect missing connections (“Opens”),
Extra Connections (“Shorts”) and misswired
connections (“wrong pins"). The test
voltage is usually 3.3 Volts D.C.
Continuous static test: this
applies a voltage to each pin in turn and checks
the response of all other pins (on the left and
right connectors of cables). Test runs N cycles.
This is checked against the required response.
This test will detect missing connections (“Opens”),
Extra Connections (“Shorts”) and misswired
connections (“wrong pins"). The test
voltage is usually 3.3 Volts D.C.
Dynamic test (model BieneCableTester01D):
this applies a 4 impuls to each pin in turn and
checks the response of all other pins (on the
left and right connectors of cables). This is
checked against the required response. This test
will detect dynamic error.
Adaptors type
- DB9,15,25,50 male and
female
- DB15,26,44 HD male
and female
- v.35 male and female
- Centronics Connectors
CN36 male and female
- SCSI Connectors MD26,
50, 68 male
- SCSI Connectors MC80,
100 male
- Telco CN50 male and
female
- IDC Flat-Cable
Connectors
- RJ11, RJ45 Connectors
- Universal adapter -
kit of universal printed
board, connectors,
spacers, screws. Use this
set to mount your
adapters.
  
Tehnical
Specifications
General
Specifications
| Cable
type: |
any
cables with connectors
from 2 to 104 pin: SCSI
Cable, CISCO Cable,
CENTRONICS Cable, RS-232
Cable... |
| Maximum
numbers of pin: |
104 or
103+ chassis pin |
| Frequence
(dynamic test): |
from
10MHz to 10 kHz (BieneCableTester01d) |
| Pin in
the net: |
< 40 |
Software
| Software
Compatibility: |
Windows
98 |
| Interface: |
Parallel
port LPT1 or LPT2 |
| Mode: |
EPP |
| Display
resolution: |
1024 x
768 |
Hardware
| Include: |
cable
tester, software, user
manual, power supply.
Adapters - after request. |
| Power
Supply: |
external |
| Phisical
Dimension |
260 x
130 x 54 mm |
| Adapter
Dimension: |
104
x 118 mm |
|
|
|
