AC Current sensors and AC Current switch

(split or solid core)
AC current switches should be used in applications in which a “Go/No Go” current switch is required. A current switch can be used to monitor fan and pump status, motors, compressors, and any other electrical equipment for proper operation. A change in the operating current may indicate mechanical failure or that the unit has been turned off.
The CSW series of AC current switches activate a normally open (NO) contact closure via a solid-state switch whenever the monitored primary circuit current exceeds a pre-set level. Models are available to switch various load types. The CSW series current switches can be used to monitor devices with a maximum continuous operating current of up to 200 Amps and the power supply is induced from the conductor being monitored.
Fixed or adjustable setpoint
The CS-F series current switches are available in a solid-core or split-core with Normally-Open (N/O) output configurations. All of these sensors will have a solid-state output with a fixed trip point (setpoint). These current switches are ideal for providing status information on any type of AC current using equipment.

Current sencor compatibel with
BR16GM-2A/-4A, BR160GM-2A/-4A, BR160SM-2A/-4A,
BR128GM-4A/-Pt1000, BR1280GM
Current switch compatibel with all our modules
BR16GM, BR160GM, BR160SM, BR128GM, BR1280GM

Ground Fault Sensor
DC Current Switch
DC Current Transducer

AKS-C NOAC Ground Fault Sensor, Factory adjusted set point.
NO output. Primary current 5 - 950 mA AC.
Normally Energized: protection from fault or loss of control power
Normally Deenergyzed: protection from faults only when control power is applied.
DKS 100 C Current Operated Switches. Input - 4-20A, 10-50A, 15-100A (with manual jumper). Hysteresis is 5% of set point. DFS 100C SDT - Relay output (SPDT) or DKS 100C NOW - Solid State Output (Normally Oupen).
DC Current Transducer. Split or solid core. 0-5VDC output DK-B5 0-10VDC output DK-B10 proportional to measured current. For DC measurement. Jumper selectable range.

DC Hall Effect Current Transducers
True RMS AC Current Transducer

The CR5200 Series, DC Hall Effect Current Transducers are designed to output a DC signal which is proportional to a DC current input signal. These devices are designed for direct current only, targeting them towards general and daily applications. 0-5Vdc or 4-20mA DC outputs. Supply Voltage: 24 VDC. The CR4100 Series True RMS Current Transducers and Transmitters are designed for applications where AC current waveforms are not purely sinusoidal. More precise and accurate than other transducers, these devices are ideal in chopped wave and phase fired control systems. 0-5Vdc or 4-20mA DC outputs.

Vegetronix Soil Moisture Sensor Probes
The VG400 which has an output range of 0 to 3V (Vegetronix Soil Moisture Sensor Probes) for low cost monitoring of soil water content. Supply Voltage 3.3V to 20 VDC. Output 0 to 3V nearly linear with moisture content.
(ask us for compatibilities with our modules types)

Tilt Sensor

Humidity and temperature sensor

Liquid Level Sensors, Flow Swithes,
Position Sensors
Gentech Procucts range
Vertically and horizontally mounted liquid level sensors. The analoque liquid level sensor. Optical level sensor.
Horizontal and vertical mounted flow switches.

Optic Leak Detection Switch
Liquid Flow Switches
Gas Flow Switches
LO10 - The general purpose optic switch is a great choice for leak detection in and around secondary containment sumps, tanks and pipes. The sensor can be applied in a broad range of chemical solutions. NO / NC Output.
FT10 - Termal Dispersion Flow Switch. Adjustable set point from .04-3 fps. The general purpose liquid flow switch is an ideal choice for a wide range of relatively clean water and chemical solutions with non-coating and/or crystallizing characteristics. The reliable solution for pump and process protection. NO / NC Output.
GT10 - Termal Dispersion Flow Switch. Adjustable set point from 1-90 fps. The general purpose gas flow switch is a great choice for a broad range of relatively clean gases with non-coating characteristics. The reliable solution for filter and process protection. NO / NC Output.

Liquid level sensor, Distance sensors

Photoelectric sensors, Inductive sensors,
Capacitive sensors, Ultrasonic sensors,
Force, strain and pressure sensors,
Magnetic sensors

Products